How do i hook up my water line to my ice maker, how to hook up a water line to a refrigerator

The sink is in the other side of the kitchen and going through the floor is not an option because I have tile. To tap into the line, shut off the water to the house at the main. The valve connected to the right side of the faucet is the cold water supply line. Answer Questions Tiling showers stall walls-Grout necessary if butted against each other?

How to Hook Up a Water Line to a Refrigerator

Twitter Facebook Pinterest Instagram. For a distance such as yours, it's best to run the flex line from behind the fridge, down through a small drilled hole in the floor next to the wall, and under the floor. Turn the cold water on the supply line clockwise to close it.

Yahoo Answers

How to Install a Water Line for a Refrigerator

Turn the water supply valve on and check for leaks. It's a good idea to have a pair of needle nose pliers handy to grab the wiring harness behind the large hole in the back of the freezer. Tighten up the mounting screws to secure the unit to the freezer wall, christian dating relationship questions and then add the ice bucket under the kit.

How to Install a Water Line for a Refrigerator

How do i hook up my water line to my ice maker
  • Go down into the crawl space.
  • Turn the supply line on once again.
  • Turn the cold water supply valve on beneath the sink.
  • Related Questions We just bought a refrigerater with an ice maker and water maker.

How to Hook Up a Water Line to a Refrigerator From the Sink

Slide the provided water valve clamp over the fill tube, insert the water supply line and use a drill with a hex head bit to tighten everything up. If there are no fixure shutoff valves, you can turn off the water by closing the main water supply valve to the entire house. You will also need a longer flex water supply tube to run from the water pipe to the refrigerator.

Do not twist the nuts too tight as this could damage the supply valve, the supply line and the adapter. If running the line through the cabinets is not feasible, you might need to run a line through the floor and up to where the refrigerator is located. Tighten the fittings as needed, using channel-type pliers or an adjustable wrench.

Home Guides
HowStuffWorks

Insert the new water line into the opening on the tee. Using the plastic tubing provided with the kit, screw the plastic fitting to the water outlet on the bottom of the solenoid valve. Measure the distance carefully, and buy a supply tube with plenty of length for the job. Thread the water line, included in the ice maker installation kit, from the area behind the refrigerator to beneath the sink.

Renovation Realities am c. Finally, turn the water back on at the main and switch the electric water heater breaker back on or turn the gas water heater to the on position. Drill as close to the back wall of the cabinet as possible, so you do not lose storage space inside the cabinet. Attach the water supply line with the provided compression fitting to the top of the solenoid valve by screwing it into place then tightening it up with a crescent wrench.

Once the water line is in place, use a screwdriver to puncture a hole in the paper cover on the back of the unit. If you are dealing with galvanized, then you will have to drill a hole and then attach the valve. If there is no water dispenser, throw away the first full batch or two of ice to make sure it is all clean and ready to use. Do I need to put my vinyl membrane behind the backer board in a shower stall? Get video instructions about kitchens, bathrooms, remodeling, flooring, painting and more.

Should I pour ammonia down a sink drain, then follow with bleach to unclog it? If so, your job is very easy. You can solve this with an ice maker installation kit that allows you to use the plumbing beneath the sink.

First, locate the shutoff valve under the kitchen sink where you want to connect the new water line. With all the work done on the back side of the freezer it's time to install the icemaker unit itself. Mount the Solenoid Valve The first part of the icemaker kit is called the solenoid valve. Install the Valve Now that the water's off, number of dating sites install the new valve for the icemaker water line. There are a few different types of valves that can be used.

You are being redirected

The kit provides you with the required parts to hook up a water line to your refrigerator. Can I hook it up to the water line from the clothes washer? All the water that comes into a residential structure should be potable, ours is hooked into the shower feed.

And along the basement ceiling, securing it to the floor joists in the basement ceiling, or drilling holes in the joists - as with running electrical wire. Tighten all three nuts on the quick-tee adapter with pliers or an adjustable wrench. When the hose reaches the area in the basement, just under the sink, a cold water pipe probably half inch will be easily accessible. Wrap the female thread on the opposite end of the adapter with thread-seal tape.

How do i hook up my water line to my ice maker

  1. Remember, with any plumbing project, once the main water supply is shut off, be sure to shut off the electric heater at the breaker or if it's gas, turn the switch to the pilot position.
  2. Tighten the connection just slightly more than hand-tight, using pliers.
  3. Turn on the cold water faucet to drain any water left in the supply line.
  4. The closest water line is my clothes washer water pipe.
  5. Now that the water's off, install the new valve for the icemaker water line.
  6. Twist the faucet supply line onto the female end of the adapter.
Report Abuse

How to Install an Icemaker

Be sure to keep the spacing equal to prevent leaking. Flex water supply tubes are available in either a tough plastic nylon mesh or braided steel. Attach the Adapt-a-Tee adapter to the shutoff valve, best app for casual tightening by hand at first. Repeat this process with the water inlet plug and the mounting hole plugs located on the side of the freezer wall.

How to Install an Icemaker

Whenever drilling holes for water lines, always be sure to use a paddle bit that's one to two sizes larger than the water supply line to prevent the line from kinking. They come in various sizes to suit whatever situation you have. Can you pour a bag of ice into an ice maker that isn't hooked up to a water line?

Now that the ice maker is completely installed, plug in the refrigerator. Running a water line to a refrigerator to supply its ice maker and drinking water dispenser has never been easier. Run the new supply tube to the back of the refrigerator. Also, check for leaks where the supply tube connects to the refrigerator before pushing the appliance back into place.

You can use any hrd cold line. Tile a homemade shower stall? Run the Water Line The first step is to run the water line.

Coil the excess water line behind the refrigerator. Pro Tip Whenever drilling holes for water lines, always be sure to use a paddle bit that's one to two sizes larger than the water supply line to prevent the line from kinking. The first part of the icemaker kit is called the solenoid valve.

  • Happy school hook up prom
  • Free chatting dating websites
  • Best hookup free apps
  • Wood dating rbb
  • Old woman online dating
  • Refrigerator water hookup under sink
  • Dating skype